ĢĒŠÄ“«Ć½

Skip to main content
Science and Technology

ā€˜Built to Fly.’ Aerospace Students Transform Sheet Metal into Working Airplane

A professor and student push a floral-patterned Rans S-21 Outbound aircraft named Velma into the sunlight at the San Luis Obispo Airport.
Written By Emily Slater | Photos by Emily Slater

On a sunny summer afternoon, a crowd pressed close to the edge of the runway at the San Luis Obispo County Regional Airport to witness the final test of a project that had taken more than a year to build. Engineering students who had helped turn crates of sheet metal into an airplane stood alongside their professor, Eric Paton, and his family, listening to the radio and scanning the runway for movement.

Two men sit in a floral-patterned airplane, taxiing out of a hangar at the airport.
Professor Eric Paton, left, and alumnus Paul Kendrick complete preflight checks in ā€œVelmaā€ before taxiing to the runway at the San Luis Obispo County Regional Airport. 

At the end of the pavement sat the airplane they had built — a floral-patterned Rans S-21 Outbound they called ā€œVelma,ā€ about to leave the ground for the first time.

Alumnus Paul Kendrick took the controls in the cockpit, with Paton in the other seat under his instruction. Together they had rehearsed every possible failure — an aborted takeoff, a turn back to the runway, a glide from higher altitude. Now came the moment of truth. The throttle went forward, and ā€œVelmaā€ charged down the runway. For a breathless few seconds, the crowd was silent. Then the plane lifted, climbing into the sky as cheers erupted below.

From Crates to Wings

Months earlier, the sight had been very different. "Velmaā€ first arrived at the San Luis Obispo airport as  a set of wooden crates filled with sheet metal and parts.  

ā€œIt started as flat-pack boxes,ā€ Paton said. ā€œPiece by piece, students turned them into something that could fly.ā€ 

The aircraft became the centerpiece of Paton’s AERO 471 course. More than 60 students took part over five quarters, learning metalwork, problem-solving and teamwork. 

Paton’s father, Neil, also had a hand in the project. A retired aerospace engineer who once worked on the Apollo 13 mission for Rockwell International, he owns the hangar where the students met twice a week. Manuals, diagrams and parts lists covered the tables, and Neil guided the students through choices the books didn’t explain. 

Two students attach the plane's propeller while the professor and his father look on.
Professor Eric Paton, center, and his father, Neil, right, work with students to attach the propeller before the airplane’s first engine startup in the hangar. 

ā€œAirplanes aren’t puzzles you can just snap together,ā€ he said. ā€œThe manuals don’t give you every step. Students had to think ahead, improvise and be honest about issues they spotted. That’s how you build safely.ā€   

The project started with the tail, then wings, then fuselage. By this summer, the work accelerated. Seats were bolted in, cables routed, rivets set one by one. Some students described it as an ā€œadult Lego challenge.ā€  

ā€œIt’s rewarding to see a flap of metal turn into a wing you know will hold up in the sky,ā€ said aerospace student Ethan Mac. 

General engineering student Kyle Marshall remembered the moment when the project shifted from scraps to something real. 

ā€œWhen the wings were off, it just looked like a bunch of pieces,ā€ he said. ā€œYou get so entrenched in the small things. Then one day you look up and think, ā€˜Looks like an airplane!ā€™ā€ 

Even small tasks, like fitting the seats with no wiggle room, felt like breakthroughs.  

Two students wearing protective eye gear work on airplane parts at a work table with an airplane in the background.
Aerospace engineering students Anthony Perez, left, and Carlos Mercado focus on final assembly work near the student-built Rans S-21 Outbound in the airport hangar.

For some, that experience went beyond the hangar. Aerospace engineering student Anthony Perez, who worked on the tail cone and cage, landed an internship as an aircraft mechanic and now plans to earn his pilot’s license. Fellow aerospace student Carlos Mercado said the project gave him tangible skills that bridged classroom theory with hands-on aviation.  

The First Roar

By winter, the wings and tail were complete. The fuselage stood on its own landing gear. What remained was the heart of the airplane.  

Students wheeled the project outside for its first engine startup. Before turning the key, they had to purge the system, priming the oil pump to be sure the engine would lubricate once it fired.  

The group crowded around the hangar doors, some with phones out, others just watching. Paton climbed into the cockpit and twisted the key. For a moment, silence. Then the engine coughed, caught and roared to life.  

Students perform final checks on a metal aircraft before its first startup at the airplane hangar.
General engineering student Kyle Marshall, front, and teammates perform final checks on the airplane’s engine before its first startup outside the hangar. 

ā€œIt was nerve-wracking,ā€ Paton admitted later. ā€œBut when it came alive, woohoo!ā€ 

He threw his hands in the air as the crowd cheered.  

For students like Isai Villanueva, who earned his pilot’s license at 17, the moment was a revelation.  

ā€œEvery detail matters,ā€ he said. ā€œThat gives me confidence when flying.ā€ 

Villanueva had joined the project on a roommate’s recommendation and worked on its early stages, then came back to see the startup. 

ā€œThis is the epitome of Learn by Doing,ā€ he said. ā€œIt’s valuable to see how an airplane comes together piece by piece.ā€ 

Past and current students stayed in touch through a group chat, alerting each other about milestones. They described the project as both a class and a family environment, a place where Neil and Eric pushed them to be honest, careful and collaborative. 

For many, the sound of that engine marked the point when the project felt real. The airplane wasn’t just a collection of parts anymore. It was alive.   

Taking Off

On the day of the aircraft’s maiden flight, Paton, Kendrick and several students spent hours in the hangar inspecting, checking and rechecking before rolling ā€œVelmaā€ out. Those final steps stretched the tension for everyone waiting nearby. 

ā€œI just want to see what it looks like in the air,ā€ said Jack Schafer, an aerospace engineering student. ā€œFingers crossed it all works.ā€ 

Around him, students swapped memories of long hours in the hangar. 

ā€œYou touched that,ā€ one joked, pointing to a section of the plane. ā€œYeah, and you riveted that,ā€ another replied. The nervous laughter carried a mix of pride and worry. 

In the cockpit, Paton was joined by Kendrick, who remembered the nerves of a first flight from his own student project years earlier, when he helped build a Van’s RV-7 still used for ĢĒŠÄ“«Ć½ā€™s flight test courses. 

ā€œWill the engine work for the entire flight? What do we do if not? There are always concerns with a new plane,ā€ he said.  

A woman hugs a man inside a floral patterned aircraft outside of an airplane hangar.
Moments before the first flight, Shelley Paton hugs her husband, Professor Eric Paton, beside ā€œVelmaā€ while their daughter Avery records the moment. 

Paton’s wife, Shelley, tried to burn off nerves with jumping jacks as she watched from the side of the runway. Their daughter, Avery, a student pilot, stood nearby. When the plane lifted off, Shelley exhaled and high-fived the group. ā€œGood job from the wife,ā€ she told the students with a laugh. 

Avery marked the moment in her own way, leaving her dad’s favorite donut in the hangar with a note that read, ā€œYou survived!ā€ 

The flight itself was careful and deliberate. Paton and Kendrick climbed to 5,500 feet, testing flap operations and evaluating flight characteristics. Designed for bush flying, ā€œVelmaā€ left the ground quickly. 

A student and professor sit in an airplane together.
Aerospace engineering student Edison Carroll and Professor Eric Paton run post-start checks after the airplane’s engine came to life for the first time outside the hangar. 

ā€œI was surprised by how little runway it needed,ā€ said Edison Carroll, an aerospace engineering student who listened in on the tower radio. ā€œBut it was built to fly.ā€  

Weeks later, Paton reflected on the milestone. By then, he had earned his tailwheel endorsement, which allows him to fly ā€œVelmaā€ without an instructor. 

ā€œThe first flight was a mix of excitement and nerves. We had rehearsed every possible emergency scenario. Thankfully, none of them happened, and the flight was a complete success. After 15 hours and about 40 landings, I can finally say ā€˜Velma’ is fun to fly.ā€  

Next Steps

For Paton, the project was never just about one airplane. He saw it as the beginning of a tradition, a

Students gather around a metallic aircraft in an airport hangar.
ĢĒŠÄ“«Ć½ students gather around the Rans S-21 Outbound as they complete assembly work in the airport hangar. 

 chance for students to take on full-scale projects that leave a mark long after graduation. This fall, Paton has begun another airplane build and hopes to boost awareness for the course so more students enroll. 

His father, Neil, saw the impact firsthand. 

ā€œI’ve worked with a lot of engineers over the years, but these students impressed me,ā€ he said. ā€œThey were careful, responsible and eager to learn.ā€ 

The project gave students more than rivets and checklists — they left with new career ambitions, practical skills and a deeper respect for aviation. 

As Schafer put it, ā€œNow we can point up and say, we built that.ā€  


Want more Learn by Doing stories in your life? Sign up for our monthly newsletter, the !